-
Welcome to Smogon! Take a moment to read the Introduction to Smogon for a run-down on everything Smogon, and make sure you take some time to read the global rules.
Instacheck Hotspot -- a fast Pokémon checker for XY
- Thread starter ΩDonut
- Start date
- Status
Use the database instead of writing a list here.
https://docs.google.com/spreadsheet/ccc?key=0Ak2hDRJIzJHbdFItaVJidTRTZTJxZnY1dThxNzRxbHc#gid=1
I looked at the database and I don't know how often it is updated but seeing as I put in an app for it two weeks ago and am still not on it I thought I might post those here seeing as only 1 is on the database.
There is at least three of the requested SVs on there, that you asked for. I made sure to check before posting it to you.
Edit: Did you select the correct database form, the one on the last page?
Correction, there are none on that list. The matching ones you found are numbers from friend codes.
Please don't correct me, when I actually took the time to look for some of them as confirmation. Thank you.
http://i30.photobucket.com/albums/c305/Mikimaru_/Pleasedontcorrectme_zps78c2bd25.png
My bad, my browser reset the amount displayed back to 250. Still there is a chance that someone has not been listed on it yet that is in here and not on there. I do apologize though.
I'm not denying that and no apologies needed everyone makes mistakes sometimes. I'm not perfect either. I have a problem with the spreadsheet. I have to scroll through manually. Since, yes, it does single out friend codes first. As for your entry, I think you possibly filled out the wrong form because I got into the database within at the most one day. Unfortunately twice due to a bug.
I filled out another one about half an hour ago and I have been added to the spreadsheet now. I contacted the people that had matches but I have never had any luck with replies in the past. People always PM me with SVs I posted in here wanting to hatch for me.
Ok, so I've poured through the troubleshooting in this guide and I'm still not finding anything that's making it work. Here is what I've done:
Installed and ran it fine the night before.
The first problem I had was connecting to the access point. It wouldn't connect today, whatsoever.
I went to my Network and Connection setting and disabled what I think was the connection that Instacheck had set up, because after doing this, it give me the "The group or resource is not in the correct state to perform the requested operation" message.
So I brought up CMD and entered the "netsh wlan set hostednetwork mode=allow" command and still got the same message.
Went back to the Network Center and brought up my ethernet connection. Turns out sharing was turned off, so I enabled it.
After that, each time I started up the Instacheck, the sharing was automatically disabled.
-sigh- Help please...? -__-
Installed and ran it fine the night before.
The first problem I had was connecting to the access point. It wouldn't connect today, whatsoever.
I went to my Network and Connection setting and disabled what I think was the connection that Instacheck had set up, because after doing this, it give me the "The group or resource is not in the correct state to perform the requested operation" message.
So I brought up CMD and entered the "netsh wlan set hostednetwork mode=allow" command and still got the same message.
Went back to the Network Center and brought up my ethernet connection. Turns out sharing was turned off, so I enabled it.
After that, each time I started up the Instacheck, the sharing was automatically disabled.
-sigh- Help please...? -__-
You don't need network sharing enabled to use Wireless Connection 2, you can try allowing the program through your firewall or running it as admin.
I gave up. i couldnt get it to work no matter what i tried.
I may be sounding like an idiot, and I apologize if I do so, since I'm new to Instacheck and everything, but it worked for me for awhile, then suddenly it stopped working for me. I did the step by step on the first page as well. It would be working fine for me, but yesterday afternoon, my 3DS would stop reading it. It said I had an internet connection and connected fine, but when I would get on Pokemon Y, it wouldn't work right. And now, whenever I try to start it up, this is the message I receive:
The service cannot accept control messages at this time. (Exception from HRESULT: 0x80070425)
I have no idea, what it is I am supposed to do now. I've never been big on computers, so I apologize if I sound like a complete idiot.
The service cannot accept control messages at this time. (Exception from HRESULT: 0x80070425)
I have no idea, what it is I am supposed to do now. I've never been big on computers, so I apologize if I sound like a complete idiot.
Anyone else having this problem?
It doesn't triple pokemon in MY list, but in the other person's it does. Makes it a huge pain to scan eggs for others.
It doesn't triple pokemon in MY list, but in the other person's it does. Makes it a huge pain to scan eggs for others.
Just restart your PC and it will work fine.
Last edited:
No way to fix that problem it just happens when the program has hiccups. I get it occasionally too, if it's happening often try disabling and enabling Wireless Connection 2Anyone else having this problem?
It doesn't triple pokemon in MY list, but in the other person's it does. Makes it a huge pain to scan eggs for others.
Just restart your PC and it will work fine.
I tried that before and it didn't work. I'll try it again just in case.Anyone else having this problem?
It doesn't triple pokemon in MY list, but in the other person's it does. Makes it a huge pain to scan eggs for others.
Just restart your PC and it will work fine.
Can anyone check about a few eggs right now?
I never had a Wireless Connection 2. It was something like "*14" but I thought that it was any extra connection that had to be done away with. So I did away with it and after that, it hasn't even made the hotspot, as opposed to before when it WOULD make the hotspot, but wouldn't makethe connection to the access point.
It can be renamed anything, but you definitely need a second virtual connection. As for the access point problem that's usually solved by either resetting the connection, allowing it through your firewall or using the command for netsh. Unfortunately, I need to go to work so I can't stand and help. I apologize.
You might be able to get it back by going into the device manager and reinstalling the driver/adapter. What did you do to get that extra one there in the first place?
It was there when I was able to pull up the access point in the first place. I'm guessing that was the Connection? Not too saavy with computers. X_x What's the name of the driver so I can try to re-install it? ANd no worries Esmeya. Thanks for the help so far. Message me later and I'll letcha know if I got it running again.
- Status